Search Results

The attractiveness of the hydraulic hybrid concept stems from the high power density and efficiency of the pump/motors and the accumulator. This is particularly advantageous in applications to heavy vehicles, as high mass translates into high rates of energy flows through the system. Using dry case hydraulic pumps further improves the energy conversion in the system, as they have 1-4% better efficiency than traditional wet-case pumps. However, evacuation of fluid from the case introduces air bubbles and it becomes imperative to address the deaeration problems. This research develops a bubble elimination efficiency testing apparatus (BEETA) to establish quantitative results characterizing bubble removal from hydraulic fluid in a cyclone deaeration device. The BEETA system mixes the oil and air according to predetermined ratio, passes the mixture through a cyclone deaeration device, and then measures the concentration of air in the exiting fluid.

A novel urea evaporation and mixing device has been developed to improve the overall performance of a urea-SCR system. The device was tested with a MY2007 Cummins ISB 6.7L diesel engine equipped with an SCR aftertreatment system. Test results show that the device effectively improved the overall NO conversion efficiency of the SCR catalyst over both steady-state and transient engine operating conditions, while NH₃ slip from the catalyst decreased.

The VanDyne SuperTurbocharger (SuperTurbo) is a turbocharger with an integral Continuously Variable Transmission (CVT). By changing the gear ratio of the CVT, the SuperTurbo is able to either pull power from the crankshaft to provide a supercharging function, or to function as a turbo-compounder, where energy is taken from the turbine and given to the crankshaft. The SuperTurbo's supercharger function enhances the transient response of a downsized and turbocharged engine, and the turbo-compounding function offers the opportunity to extract the available exhaust energy from the turbine rather than opening a waste gate. Using 1-D simulation, it was shown that a 2.0-liter L4 could exceed the torque curve of a 3.2L V6 using a SuperTurbo, and meet the torque curve of a 4.2-liter V8 with a SuperTurbo and a fresh-air bypass configuration. In each case, the part-load efficiency while using the SuperTurbo was better than the baseline engine.

For transmission suppliers tooled primarily for producing manual transmissions, retrofitting a manual transmission with actuators and a controller is business viable. It offers a low cost convenience for the consumer without losing fuel economy when compared to torque converter type automatics. For heavy duty truck fleets even the estimated 3% gain in fuel economy that the Automated Manual Transmission (AMT) offers over the manual transmission can result in lower operational costs. This paper provides a case study using a light duty transmission retrofitted with electric actuation for gears and the clutch. A high level description of the control algorithms and hardware is included. Clutch control is the most significant component of the AMT controller and it is addressed in detail during operations such as vehicle launch from rest, launch from coast and launch on grades.

The US Army is currently seeking to reduce fuel consumption by utilizing fuel efficient lubricants in its ground vehicle fleet. An additional desire is for a lubricant which would consist of an all-season (arctic to desert), fuel efficient, multifunctional Single Common Powertrain Lubricant (SCPL) with extended drain capabilities. To quantify the fuel efficiency impact of a SCPL type fluid in the engine and transmission, current MIL-PRF-46167D arctic engine oil was used in place of MIL-PRF-2104G 15W-40 oil and SAE J1321 Fuel Consumption In-Service testing was conducted. Additionally, synthetic SAE 75W-140 gear oil was evaluated in the axles of the vehicles in place of an SAE J2360 80W-90 oil. The test vehicles used for the study were three M1083A1 5-Ton Cargo vehicles from the Family of Medium Tactical Vehicles (FMTV).

This study utilizes an eddy current proximity probe to approximate the acceleration of a valve in a SOHC valve train. Several techniques are discussed for extrapolating acceleration data from displacement data through numerical differentiation. The data were compared to acceleration data as measured by an accelerometer mounted on the valve face. It was found that valve train acceleration behavior can be reasonably approximated using displacement data as measured by a proximity probe when differentiated using a three-point, Lagrangian interpolation. But the frequency response of the proximity probe is severely restricted by the limitations of the measurement and data collection instrumentation, the limitations of the differentiation method and the continuity of the base measured data.

In-cylinder ion sensing through sparkplug electrodes can be used to determine in-cylinder A/F ratio by using a modified production coil-on-plug ignition system having ion sensing capability. The in-cylinder ionization can be characterized by the height of the peak, location of the peak from ignition command and area under the ionization signal curve. The effects of A/F ratio on the in-cylinder ionization can be isolated from other affecting factors by conducting tests on a constant volume combustion device in which the initial pressure and temperature can be well controlled. This results in a parabolic correlation of the ionization characteristics with the mixture equivalence ratio. Additionally the ionization characteristics show strong dependence on engine load and speed. Equivalence ratio characteristics during engine cranking and warm up are investigated, and a method for on-line calibration of ionization detection is discussed.

A technique was developed for measuring the Laminar Burning Velocity (LBV) of multi-component fuel blends for use in high-performance spark-ignition engines. This technique involves the use of a centrally-ignited spherical combustion chamber, and a complementary analysis code. The technique was validated by examining several single-component fuels, and the computational procedure was extended to handle multi-component fuels without requiring detailed knowledge of their chemical composition. Experiments performed on an instrumented high-speed engine showed good agreement between the observed heat-release rates of the fuels and their predicted ranking based on the measured LBV parameters.

DiMethyl Ether (DME) has been shown to be a very attractive fuel for low emission direct injection compression ignition (DICI) engines. It combines the advantages of the high efficiencies of diesel cycle engines with soot free combustion. However, its greatest drawback is the need to develop new fuel injection and handling systems. Previous approaches have been common rail type injection systems which have shown great potential in reducing harmful exhaust emissions and achieving good engine performance and efficiency due to good control of both the fuel injection characteristics and temperature. The concept also has proven benefits with respect to convenient and safe fuel handling. The logical evolution of this concept simplifies the fuel system and avoids special components for DME handling such as high pressure rail pumps while retaining all the benefits of the common rail principle.

The Tank-Automotive RD&E Center periodically conducts foreign materiel evaluations to assess the current state of the art for ground vehicle technologies. The Propulsion Laboratory is conducting performance evaluations of an opposed-piston two-stroke diesel tank engine produced by the Kharkov Design Bureau in Ukraine. A key factor in the performance of all two-stroke engines is the scavenging process, which determines how well the cylinders are emptied of exhaust and filled with fresh air. The overall air flow rate is not sufficient to determine this, as a significant amount of air may be lost through the exhaust ports during the scavenging process. The inlet tracer gas method was employed to provide the additional data required. With methane as the tracer, it produced reasonable and consistent data over a wide range of engine speeds and loads. The inlet tracer gas method was found to be an effective tool for measuring the scavenging performance of a running two-stroke diesel engine.

The effect of low temperature intake air on the knock limited brake mean effective pressure (BMEP) in a spark ignited natural gas engine is described in this paper. This work was conducted to demonstrate the feasibility of using the vaporization of liquefied natural gas (LNG) to reduce the intake air temperature of engines operating on LNG fuel. The effect on steady-state emissions and transient response are also reported. Three different intake air temperatures were tested and evaluated as to their impact upon engine performance and gaseous emissions output. The results of these tests are as follows. The reduced intake air temperature allowed for a 30.7% (501 kPa) increase in the knock-limited BMEP (comparing the 10°C (50°F) intake air results with the 54.4°C (130°F) results). Exhaust emissions were recorded at constant BMEP for varying intake air temperatures.

In off-highway applications the engine torque is distributed between the transmission (propulsion) and other accessories such as power steering, air conditioning and implements. Electronic controls offer the opportunity to more efficiently manage the control of the engine and transmission as an integrated system. This paper deals with development of a steepest descent algorithm for maximizing the efficiency of hydrostatic transmission along with the engine in the presence of accessory load. The methodology is illustrated with an example. The strategy can be extended to the full hydro-mechanical configuration as required. Applications of this approach include adjusting for component wear and intelligent energy management between different accessories for possible size reduction of powertrain components. The potential benefits of this strategy are improved fuel efficiency and operator productivity.

In recent years there has been an increased interest in the continuously variable split power transmissions as these drive units are capable of vehicle launches and directional changes without using clutches. These tasks are accomplished by appropriately splitting power between the fixed mechanical and variable ratio branches. The power is recombined at the transmission output. A properly designed split power transmission arrangement will improve vehicular agility and reduce variator size. This paper provides characteristics of six single stage input coupled continuously variable toroidal split power transmission arrangements. Mathematical equations are derived for speed, torque and power. A computer program that utilizes the capabilities of Matlab is developed. The program calculates the required fixed and variable branch gear ratios for the predefined variator, planetary and overall transmission ratios.

Vehicle designers make use of vehicle performance programs such as RAPTOR™ to predict the performance of concept vehicles over ranges of industry standard drive cycles. However, the accuracy of such predictions may be greatly influenced by factors requiring more specialist simulation capabilities. For example, fuel economy prediction will be heavily influenced by the performance of the engine cooling system and its impact on the vehicle's aerodynamic drag, and the load from the air-conditioning system. To improve the predictions, specialist simulation capabilities need to be applied to these aspects, and brought together with the vehicle performance calculations through co-simulation. This paper describes the approach used to enable this cosimulation and the benefits achieved by the vehicle designer.

Two different laboratory fuel-injection-pump durability-tests were conducted with four advanced technology test fuels. The first test used a relatively low pressure rotary, opposed piston fuel injection pump similar to those used on some current North American engines. The second test used a relatively high pressure common rail injection pump such as those used currently on some European engines. The tests were scheduled to operate for 500 hours under severe load conditions. It can be concluded that the common-rail, high-pressure fuel pump is more sensitive to the advanced fuels than is the rotary pump in this severe duty-cycle test. Although the laboratory high frequency reciprocating rig (HFRR) tests were able to distinguish between those fuels that contained lubricity additives and those that did not, there was little correlation with pump durability results.

This oil category was driven by two new cooled exhaust gas recirculation (EGR) engine tests operating with 15% EGR, with used oil soot levels at the end of the test ranging from 6 to 9%. These tests are the Mack T-10 and Cummins M11 EGR, which address ring, cylinder liner, bearing, and valve train wear; filter plugging, and sludge. In addition to these two new EGR tests, there is a Caterpillar single-cylinder test without EGR which measures piston deposits and oil consumption control using an articulated piston. This test is called the Caterpillar 1R and is included in the existing Global DHD-1 specification. In total, the API CI-4 category includes eight fired-engine tests and seven bench tests covering all the engine oil parameters. The new bench tests include a seal compatibility test for fresh oils and a low temperature pumpability test for used oils containing 5% soot. This paper provides a review of the all the tests, matrix results, and limits for this new oil category.

Although the toroidal continuously variable transmission (CVT) has been successfully introduced into the automotive market, it has not been developed for the motorcycle community even though manufacturers have shown interest. Further, little information is available with regards to their application in motorcycles. To aid in the development process, continuously variable toroidal transmission design concepts for a motorcycle application are presented. Alternate packaging configurations developed in this paper represent potential future motorcycle transmission arrangements. Variator design parameters and their effect on transmission operation are discussed. Both single and dual cavity designs as well as orientation of the engine and final drive are reviewed.

The use of small-hole diesel injector tips and high injection pressures was investigated as a countermeasure to the increased particulate matter (PM) emissions formed when using exhaust gas recirculation (EGR) in diesel engines. This study examined the use of injector tip hole sizes down to about 0.09-mm (0.0035 in.), and injection pressures to 300 MPa (3000 bar, or 43,500 psi). The first phase of these studies was conducted in a high-temperature, high-pressure combustion bomb, with supporting calculations using a unit injector model, a jet-mixing model, and a diesel jet evaporation model. The second phase was conducted in a commercial diesel engine of 12.7-liter displacement designed to meet U.S. 1998 emissions levels. Engine tests were conducted with a baseline cam and a faster rise-rate cam, and three different hole tip sizes. The cams consisted of a baseline cam and a cam of similar design, but with a 12 percent faster rise rate.

Split power transmissions are often a viable power path for continuously variable powertrains. The planetary gear set is the central mechanism of these powerpaths which creates the possibility for numerous configurations. Determining the right configuration for a specific application can thus be complicated if the designer does not have an easy way to evaluate each configuration. This paper will address this issue. The different split power configurations are explored. Speed ratio and torque ratio formulas for the different configurations are introduced. An efficient and simple method to determine positive and negative power flow is also demonstrated. The development of tractive effort curves is discussed as a methodology to determine the theoretical performance of any configuration with an emphasis on the use of hydraulics as the variator.

Continuously variable split power transmissions can offer a clutchless transition from reverse through neutral and into the forward driving mode. This is accomplished by splitting the input power between fixed ratio and variable ratio branches and recombining the power with a planetary set. Further, these transmissions offer seamless ratio changes throughout their range. In contrast to these benefits, single stage designs can suffer from recirculated power, which increases the power level through the variator. This results in the need for a larger variator, which reduces efficiency and increases weight and inertia. In addition, single stage designs can experience high planetary member speeds as a result of a wide transmission ratio range. Seven dual stage input coupled transmission models are developed in an effort to reduce the recirculated power and high planetary member speeds found in the single stage designs. Speed, torque and power models are developed in Matlab and Excel.